Knob-and-Tube, Aluminum Wiring and Poly-B Pipes in Older BC Homes
Some older homes still have wiring and pipes that insurers ask about and home inspectors look for, and that can matter to your lender: knob-and-tube or aluminum wiring, grey Poly-B water pipe, and galvanized steel or lead water lines. For BC buyers and homeowners, here is what each one is, the years it's associated with, why it matters when you buy or insure a home, what an inspection can tell you, and when to call a licensed electrician or plumber.
The short version
Knob-and-tube wiring is associated with homes built before about 1945, aluminum branch wiring with some homes from the 1960s and 1970s, and grey Poly-B pipe with homes built or replumbed from the 1970s into the 1990s. Health Canada says the National Plumbing Code allowed lead pipe until 1975 and galvanized steel pipe until 1980. None of these automatically rules a home out, but insurers may ask about them, and most lenders want proof of insurance before they advance funds. An inspection is visual, so it can't tell you what's inside the walls. If the inspector flags any of these, book a licensed electrician or plumber during your subject period, get written quotes and call your insurer before you remove subjects.
Knob-and-tube wiring
Knob-and-tube is an early wiring method: copper wires run through porcelain knobs and tubes that hold and protect them, with no ground wire. The Insurance Bureau of Canada (IBC) associates it with homes built from 1900 to 1945, and notes that the ground wire it lacks plays an important role in preventing shock.
In a renovated home, some circuits may have been replaced and others not, so ask whether any knob-and-tube is still in use. IBC adds that its rubberized cloth covering can deteriorate with age, exposing the wire. Have a licensed electrical contractor assess its condition and quote any repairs or replacement.
Aluminum wiring
Aluminum branch wiring, the circuits that run from the electrical panel to outlets, switches and lights, was used in some homes built in the 1960s and 1970s as a cheaper, lighter alternative to copper. Much of the concern is at the connections: IBC explains that aluminum expands and contracts more than copper, which can loosen connections, and that it was often installed incorrectly.
- Have the connections checked. Ask a licensed electrical contractor who is familiar with aluminum wiring to assess the connections and repair any that need it, under a permit.
- Use parts rated for aluminum. Even a replacement switch or outlet has to be rated for aluminum wire, so it isn't a simple swap.
- Ask what was done. If a seller says the wiring was repaired, ask for the permit and the electrician's invoice.
Poly-B water pipes
Poly-B, short for polybutylene, is a flexible plastic water supply pipe, usually light grey. It was installed in homes from the 1970s into the 1990s, and production ended in 1998, after suppliers stopped making its resin.
- Where to look. Wherever pipes are exposed: at the water heater, under sinks, near the main water shut-off and in an unfinished basement or crawl space.
- Why it matters. IBC says Poly-B is prone to breaking, which can lead to leaks and water damage, and that some insurers may limit coverage for it, so ask yours how it treats Poly-B.
- Replacing it. A repipe, replacing the supply lines, can mean opening walls and ceilings, so ask whether a quote includes the plumbing permit and patching.
Galvanized steel, lead pipes and your tap water
Galvanized steel pipe corrodes from the inside over time, which IBC says can cause leaks. It can also hold lead: Health Canada notes that galvanized iron plumbing can collect lead and release it even after the original source has been removed. Lead pipe was allowed for the service line to a home until 1975, and lead can also come from older solder and brass fittings. HealthLink BC says BC's plumbing code restricted lead in plumbing in 1989, so homes built before then may be at higher risk.
Health Canada's guideline for lead in drinking water is a maximum of 0.005 mg/L, measured at the tap, and pregnant people, infants and children are the most vulnerable. HealthLink BC's advice:
- Run the cold tap. First thing in the morning, or after water has sat in the pipes for several hours, let it run for 1 to 5 minutes or until it turns colder.
- Use cold water for drinking and cooking. Boiling doesn't remove lead and may increase its concentration.
- Test. Have a laboratory test a sample, and contact your local health authority's environmental health officer with any concerns.
- Filter if needed. Use a device certified to NSF International's standard for lead removal at the tap you use most, and maintain it.
A lasting fix means replacing the source. Health Canada notes that the city usually owns one part of the service line and the homeowner the other, so ask your city what it knows about your line and whether it has a replacement program.
Insurance, lenders and the home inspection
IBC says insurers will ask about knob-and-tube or aluminum wiring and about fuses or electrical service under 100 amps, and may require updated wiring, at least 100-amp service or an electrical inspection. It also says galvanized steel and lead pipes are more likely to crack and leak. This affects financing too: People's Law School notes that most lenders require proof of insurance before they will provide any funds.
Consumer Protection BC, which licenses home inspectors, says an inspection is visual only. The inspector can report what's exposed, such as the electrical panel or the pipes at the water heater, but not what's inside finished walls, and the report must list the areas where you should get expert advice; see Home Inspections in BC. Then call your insurer or broker with what the inspector and any specialist found, and see Home Insurance for Houses in BC.
Permits and licensed trades
- Electrical work. Technical Safety BC says that, by law, only qualified people employed by licensed contractors can do regulated electrical work, under a permit. A homeowner permit is the exception, only for a detached house that you alone own and live in with your family, with no suite; strata and duplex owners can't get one.
- Who issues the permit. Technical Safety BC in most of BC, but some cities issue their own electrical permits, including Vancouver, Burnaby, Surrey, Maple Ridge, West Vancouver and the City and District of North Vancouver.
- Partial upgrades. Technical Safety BC's guidance lets existing circuits that are adequate for their purpose stay when part of a house is rewired; a complete rewire must meet the current code. Ask the electrician which circuits can stay.
- Plumbing work. Plumbing permits come from your city or regional district, not Technical Safety BC, and each sets out which work needs one, so ask before a repipe or service line replacement starts.
Get more than one written quote, and keep the permits, final inspection records and invoices; they answer an insurer's questions and, later, a buyer's. See Hiring a Contractor in BC.
Buying and selling
If you're buying, plan these checks around your subject period:
- Allow enough time. Book the inspection early, so there's room for an electrician or plumber, quotes and a call to your insurer before your subject removal date; see Subject Clauses in BC.
- Ask for records. Permits and invoices for any rewiring or repiping, and the year it was done.
- Use the quotes. A written quote gives you a figure to discuss with the seller, as a price change, a credit or repairs; see After the Home Inspection.
If you're selling, BCFSA says sellers have a common-law duty to disclose latent defects to a buyer, and the rules for real estate licensees count a lack of required permits as a material latent defect, which a seller's agent must disclose once they know of it. Gather the records of past upgrades so you can answer questions accurately, and if you're unsure what must be disclosed, ask your real estate agent or a lawyer; see The Property Disclosure Statement.
Questions buyers and homeowners often ask me
Can I get home insurance on a house with knob-and-tube wiring?
It depends on the insurer. Some may ask for an electrician's inspection or updated wiring before they offer or renew coverage. Call your insurer or broker with what the inspector and electrician found before you remove subjects.
Does aluminum wiring have to be replaced?
Not necessarily. A licensed electrical contractor can assess the connections and repair them under a permit, using parts rated for aluminum. Some insurers may still ask for upgrades or proof of the work, so ask yours what it needs before you remove subjects.
How can I tell if a house has Poly-B pipes?
Look at exposed pipe near the water heater, under sinks or at the main shut-off. Poly-B is flexible, light grey plastic, printed with markings that include its standard, CSA B137.8. A plumber can confirm it and tell you how much of the house has it.
How do I find out if there's lead in my tap water?
Have a laboratory test it. HealthLink BC says a sample taken first thing in the morning, before any water is used, will generally show a problem. Your water supplier can tell you about its system, and your health authority can help if you have concerns.
Will a home inspection tell me what's inside the walls?
No. In BC, a home inspection is visual only, so the inspector reports on what can be seen. If the report points to the wiring or plumbing, have a licensed electrician or plumber look further before you remove subjects.
More on older homes: start with my guide to buying an older home in BC, then read about asbestos, vermiculite and lead paint and underground oil tanks.
Looking at an older home?
I can help you plan inspections and specialist checks before you remove subjects, and connect you with licensed trades. Call or text 778-834-1706, email silvana@silvanaazurdia.ca or send me a message. Happy to help in English or Spanish.
This article is general information, not legal, insurance or professional advice. The details come from Technical Safety BC, Health Canada, HealthLink BC, the Insurance Bureau of Canada, Consumer Protection BC, BCFSA, People's Law School, the Government of Alberta and city permit pages, and were current at the time of writing; insurers and cities set their own requirements, so check with yours. For permits and who can do electrical work at home, see Technical Safety BC's guide to home modifications.
Recent Posts











